פורסם: 17/12/2014 - 13:16
נושא ההודעה: האם הדיסק הזה הולך למות
|
יש לי בעיה עם דיסק smart נותן כל הזמן הודעות שגיאה על bad sectors אבל זה תמיד אותו סקטור. השאלה היא האם הדיסק דפוק והאם יחליפו לי אותו (עדיין תחת אחריות) כי המחשב כאילו עובד תקין. הדיסק פעם אחת השמיע קולות של הולך למות אבל מאז הוא עובד בסדר לכאורה.
קוד: |
smartctl 6.3 2014-07-26 r3976 [i686-w64-mingw32-win7] (sf-6.3-1)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Deskstar 7K1000.D
Device Model: Hitachi HDS721050DLE630
Serial Number: MSK4235H30B3TH
LU WWN Device Id: 5 000cca 37cea7043
Firmware Version: MS1OA610
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Dec 17 12:21:48 2014 GTBST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4703) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 79) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 65536
2 Throughput_Performance 0x0005 136 136 054 Pre-fail Offline - 90
3 Spin_Up_Time 0x0007 120 120 024 Pre-fail Always - 191 (Average 190)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 1790
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 31
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 115 115 020 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 1414
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1790
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1817
193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1817
194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 18/43)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 46
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 57 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 57 occurred at disk power-on lifetime: 1411 hours (58 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 c8 bb 48 0e Error: UNC 8 sectors at LBA = 0x0e48bbc8 = 239647688
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 10 c0 bb 48 e0 00 00:48:39.634 READ DMA EXT
25 00 08 b8 bb 48 e0 00 00:48:39.634 READ DMA EXT
ea 00 00 00 00 00 a0 00 00:48:39.593 FLUSH CACHE EXT
35 00 08 28 f2 03 e0 00 00:48:39.593 WRITE DMA EXT
35 00 08 90 6b 64 e0 00 00:48:39.593 WRITE DMA EXT
Error 56 occurred at disk power-on lifetime: 1411 hours (58 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 c8 bb 48 0e Error: UNC 8 sectors at LBA = 0x0e48bbc8 = 239647688
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 10 c0 bb 48 e0 00 00:48:35.741 READ DMA EXT
25 00 08 b8 bb 48 e0 00 00:48:35.741 READ DMA EXT
ea 00 00 00 00 00 a0 00 00:48:35.665 FLUSH CACHE EXT
35 00 08 28 f2 03 e0 00 00:48:35.665 WRITE DMA EXT
35 00 08 90 6b 64 e0 00 00:48:35.664 WRITE DMA EXT
Error 55 occurred at disk power-on lifetime: 1411 hours (58 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 c8 bb 48 0e Error: UNC 8 sectors at LBA = 0x0e48bbc8 = 239647688
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 10 c0 bb 48 e0 00 00:48:31.854 READ DMA EXT
25 00 08 b8 bb 48 e0 00 00:48:31.854 READ DMA EXT
25 00 40 d0 b9 3d e0 00 00:48:31.854 READ DMA EXT
ea 00 00 00 00 00 a0 00 00:48:31.854 FLUSH CACHE EXT
25 00 10 c0 bb 48 e0 00 00:48:28.050 READ DMA EXT
Error 54 occurred at disk power-on lifetime: 1411 hours (58 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 c8 bb 48 0e Error: UNC 8 sectors at LBA = 0x0e48bbc8 = 239647688
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 10 c0 bb 48 e0 00 00:48:28.050 READ DMA EXT
25 00 08 b8 bb 48 e0 00 00:48:28.050 READ DMA EXT
ea 00 00 00 00 00 a0 00 00:48:28.003 FLUSH CACHE EXT
35 00 08 a0 0f 5f e0 00 00:48:28.003 WRITE DMA EXT
35 00 08 28 f2 03 e0 00 00:48:28.003 WRITE DMA EXT
Error 53 occurred at disk power-on lifetime: 1411 hours (58 days + 19 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 18 c8 bb 48 0e Error: UNC 24 sectors at LBA = 0x0e48bbc8 = 239647688
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 20 c0 bb 48 e0 00 00:48:24.030 READ DMA EXT
25 00 08 b8 bb 48 e0 00 00:48:24.030 READ DMA EXT
25 00 40 90 b9 3d e0 00 00:48:24.030 READ DMA EXT
25 00 40 78 cc 34 e0 00 00:48:24.030 READ DMA EXT
25 00 00 78 cb 34 e0 00 00:48:24.029 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 70% 1412 239647688
# 2 Extended offline Completed: read failure 70% 1411 239647688
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
|
מה אתם אומרים?
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 14:12
נושא ההודעה:
|
אם אני לא טועה, הדיסקים של Hitachi Deskstar הם אמינים ואכותיים למדי.
גם לי יש דיסק שמיצר קולות של "גסיסה"... כבר כמה שנים ועדיין חי ובועט - לא נראה לי שהוא עומד להתפגר בזמן הקרוב.
לכל מקרה, גיבוי חיצוני כדאי לעשות.
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 14:40
נושא ההודעה:
|
גיביתי כבר. אבל בכל זאת מה עם ה- bad sectors?
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 14:45
נושא ההודעה:
|
אם הוא באחריות - אל תהסס. החלף. "קצת bad sectors" זה כמו "קצת בהריון".
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 17:37
נושא ההודעה:
|
אם הדיסק הפסיק להרעיש כנראה שסמארט סימן אותו והדיסק לא ניגש אליו יותר.
יכול להיות שהדיסק ישאר כך עד סוף חייו אבל מנסיוני ל bad sectors
יש נטיה להתפשט (או להתרבות) ואתה עלול להתקל בעוד כאלו.
לדעתי הם צריכים להחליף לך אותו.
איציק
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 17:44
נושא ההודעה:
|
תודה על התגובות. אני ינסה להחליף.
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 17:50
נושא ההודעה:
|
Anonymous : | תודה על התגובות. אני ינסה להחליף. |
*אנסה
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 18:22
נושא ההודעה:
|
Anonymous : | Anonymous : | תודה על התגובות. אני ינסה להחליף. |
*אנסה |
מודעה באתר הכרויות: מחפשת בחור שמשתמש בגוף ראשון עתיד.
תגובה: אני יכיר לך מישהו.
|
|
חזרה לתוכן הדיון |
פורסם: 17/12/2014 - 19:30
נושא ההודעה:
|
מתחם הבורסה לידך. בשביל מה אתה צריך אתר כזה?
|
|
חזרה לתוכן הדיון |
פורסם: 20/12/2014 - 15:15
נושא ההודעה:
|
לפני שגולשים לדברים יותר מעניינים מה שמוזר זה שהוא כל פעם מדווח על אותן שגיאות. כלומר אם הוא סימן את הסקטורים האלה כפגומים הוא לא אמור לדווח על זה כל פעם כשגיאות בלוג לא?
הייתי משאיר אותו כי זה נראה ארוע חד פעמים אבל משום מה מספר השגיאות גדל אבל אלא אותן שגיאות.
קוד: |
ATA Error Count: 152 (device log contains only the most recent five errors)
|
לעומת מקודם רק 53. הוא לא אמור פשוט לסמן את זה כסקטורים פגומים וזהו?
מה אני לא מבין?
|
|
חזרה לתוכן הדיון |
פורסם: 31/12/2014 - 23:32
נושא ההודעה:
|
זהו מת. טוטאל לוסט.
|
|
חזרה לתוכן הדיון |
פורסם: 01/01/2015 - 18:42
נושא ההודעה:
|
יכול להיות שאתה צריך להגיד לו - איכשהו - לסמן אותם.
איציק
|
|
חזרה לתוכן הדיון |
|