ווטסאפ - לינוקס, BSD, קוד פתוח ותוכנה חופשית בעברית. Whatsup - Linux, BSD, open source and free software in Hebrew

 
 
  כניסת חברים · רישום · שכחתי סיסמה  
tux the penguin
תגובה לנושא
צפיה בנושא הבא Printable version התחבר כדי לבדוק הודעות פרטיות צפיה בנושא הקודם
אורח · ·
 

הודעה פורסם: 18/11/2014 - 22:22
נושא ההודעה: אינטרנט מנותק

שלום חבר'ה

יש לי דיביאן 7 והבעיה שלי שאחרי כמה דקות שאני מחובר לאינטרנט הוא מתנתק לי יש למישהו רעיון?
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 18/11/2014 - 23:15
נושא ההודעה:

לכתוב עוד פרטים יהיה רעיון מצוין.
בוא נתחיל באיך אתה מחובר, חיבור קווי או אלחוטי?
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אלכס___אורח · ·
 

הודעה פורסם: 18/11/2014 - 23:19
נושא ההודעה: טיפ

שלום לך אורח.

אתה צריך לספק יותר פרטים על המערכת שלך, כמו איך אתה מחובר לאינטרנט. כמה שיותר פרטים, יותר קל היה לזהות את הבעיה ולעזור לך.

0. מתי החלה הבעיה? אחרי אדכון\פתאום\מרגע ההתקנה.
1. איזה סוג חיבור אתה משתמש על\חוטי\נט-סטיק.
2. באיזה תוכנה אתה משתמש להתחברות (network mang.. או מה שהוא אחר).
3. הגדרות רשת אוטומטית\ידנית?
4. איזה סוג חומה את משתמש כרטיס רשת-נתב-מודם.
5. וכל פיסת מידעה נוספת שאתה חושב שיכולה לתרום לאיתר הבעיה.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 19/11/2014 - 21:18
נושא ההודעה:

צודקים טעות שלי

1.) אני מחובר ברשת אלחוטית

2.)לא יודע אם זה קרה אחרי עידכו כל שהוא לא שמתי לב

3.)תוכנה כידי להתחבר להאינטרנט לא אין יש לי כרטיס רשת
Network controller: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] (rev 34)


הגדרת רשת אוטומטית

ואני משתמש בhotbox של חברת הוט

אבל שאני מתחשב בקווי הכל עובד כמו שצריך
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 20/11/2014 - 01:19
נושא ההודעה:

כמה מחשבים יש בבית? אתה גר באזור צפוף עם הרבה שכנים? מה המרחק ממחשב שיש בוא את התקלה לHOTBOX?
תנסה חהתקין את בדריבר מחדש לפי הוראות פה
https://wiki.debian.org/iwlwifi

בנוסף תתקין גם את החבילות הללו.
קוד:
wireless-regdb
crda


עם התקלה חוזרת על עצמנה תכתוב בטרמינל dmesg ותדביק פו את הפלת בצורה מסודרת.
הצלחה.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 29/11/2014 - 19:05
נושא ההודעה:

תודה לעוזרים

יש לציין שאם אני מתחבר דרך הטלפון שלי בwifi אני מצליח לגלוש מצויין בלי ניתוקים אבל דרך הראוטר אני מתנתק אין בעיה בראטור זה מה שhot אומרים ויש לנו בערך חמישה מכשרים שגולשים דרך הראוטר ולכולם אין בעיות חוץ מהמחשב שלי

הנה הפלט

קוד:
[    6.590512] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni)
[    6.626041] input: Dell WMI hotkeys as /devices/virtual/input/input6
[    6.663697] ACPI: resource 0000:00:1f.3 [io  0xf040-0xf05f] conflicts with ACPI region SMBI [io 0xf040-0xf04f]
[    6.663700] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[    6.722402] ACPI: Battery Slot [BAT0] (battery present)
[    6.722581] ACPI: AC Adapter [AC] (off-line)
[    6.765997] [drm] Initialized drm 1.1.0 20060810
[    6.859339] cfg80211: Calling CRDA to update world regulatory domain
[    7.229471] i915 0000:00:02.0: setting latency timer to 64
[    7.246233] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
[    7.246234] [drm] MTRR allocation failed.  Graphics performance may suffer.
[    7.246372] i915 0000:00:02.0: irq 53 for MSI/MSI-X
[    7.246378] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    7.246379] [drm] Driver supports precise vblank timestamp query.
[    7.247646] [drm:intel_dsm_platform_mux_info] *ERROR* MUX INFO call failed
[    7.247713] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=none:owns=io+mem
[    7.247715] vgaarb: transferring owner from PCI:0000:00:02.0 to PCI:0000:01:00.0
[    7.323521] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
[    7.323523] Copyright(c) 2003-2011 Intel Corporation
[    7.323640] iwlwifi 0000:09:00.0: setting latency timer to 64
[    7.323663] iwlwifi 0000:09:00.0: pci_resource_len = 0x00002000
[    7.323665] iwlwifi 0000:09:00.0: pci_resource_base = ffffc900057b0000
[    7.323667] iwlwifi 0000:09:00.0: HW Revision ID = 0x34
[    7.323755] iwlwifi 0000:09:00.0: irq 54 for MSI/MSI-X
[    7.323791] iwlwifi 0000:09:00.0: Detected Intel(R) Centrino(R) Wireless-N 1030 BGN, REV=0xB0
[    7.323850] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[    7.340744] iwlwifi 0000:09:00.0: device EEPROM VER=0x71a, CALIB=0x6
[    7.340745] iwlwifi 0000:09:00.0: Device SKU: 0X150
[    7.340747] iwlwifi 0000:09:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3
[    7.340765] iwlwifi 0000:09:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels
[    7.409895] input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input7
[    7.574252] iwlwifi 0000:09:00.0: firmware: agent loaded iwlwifi-6000g2b-6.ucode into memory
[    7.574259] iwlwifi 0000:09:00.0: loaded firmware version 18.168.6.1
[    7.574647] Registered led device: phy0-led
[    7.654554] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[    7.768016] MXM: GUID detected in BIOS
[    7.768550] VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG0.PEGP handle
[    7.768570] nouveau 0000:01:00.0: power state changed by ACPI to D0
[    7.768573] nouveau 0000:01:00.0: power state changed by ACPI to D0
[    7.768576] nouveau 0000:01:00.0: enabling device (0006 -> 0007)
[    7.814726] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[    7.815919] fbcon: inteldrmfb (fb0) is primary device
[    7.815996] Bluetooth: Core ver 2.16
[    7.816011] NET: Registered protocol family 31
[    7.816012] Bluetooth: HCI device and connection manager initialized
[    7.816014] Bluetooth: HCI socket layer initialized
[    7.816016] Bluetooth: L2CAP socket layer initialized
[    7.816021] Bluetooth: SCO socket layer initialized
[    7.829221] Bluetooth: Generic Bluetooth USB driver ver 0.6
[    7.829332] usbcore: registered new interface driver btusb
[    8.225252] Console: switching to colour frame buffer device 170x48
[    8.232175] fb0: inteldrmfb frame buffer device
[    8.232177] drm: registered panic notifier
[    8.232383] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[    8.252683] acpi device:1c: registered as cooling_device4
[    8.252887] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:1a/LNXVIDEO:00/input/input8
[    8.252941] ACPI: Video Device [PEGP] (multi-head: yes  rom: yes  post: no)
[    8.253729] acpi device:3b: registered as cooling_device5
[    8.253922] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input9
[    8.253964] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    8.253985] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    8.254181] nouveau 0000:01:00.0: setting latency timer to 64
[    8.254210] [drm] nouveau 0000:01:00.0: Detected an NVc0 generation card (0x0c1a80a1)
[    8.254274] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[    8.254304] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[    8.257344] vga_switcheroo: enabled
[    8.257360] [drm] nouveau 0000:01:00.0: Checking PRAMIN for VBIOS
[    8.267078] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[    8.267080] [drm] nouveau 0000:01:00.0: Checking PROM for VBIOS
[    8.267139] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[    8.267141] [drm] nouveau 0000:01:00.0: Checking ACPI for VBIOS
[    8.318585] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[    8.325042] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
[    8.325127] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[    8.442431] Linux media interface: v0.10
[    8.570354] Linux video capture interface: v2.00
[    8.591152] uvcvideo: Found UVC 1.00 device Laptop_Integrated_Webcam_HD (0c45:6483)
[    8.635798] cfg80211: World regulatory domain updated:
[    8.635803] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.635808] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    8.635813] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    8.635817] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[    8.635821] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[    8.635824] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[    8.635828] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[    8.635832] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[    8.635836] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[    8.856976] input: Laptop_Integrated_Webcam_HD as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.5/1-1.5:1.0/input/input13
[    8.857089] usbcore: registered new interface driver uvcvideo
[    8.857093] USB Video Class driver (1.1.1)
[   10.038715] [drm] nouveau 0000:01:00.0: ... appears to be valid
[   10.038725] [drm] nouveau 0000:01:00.0: Using VBIOS from ACPI
[   10.038734] [drm] nouveau 0000:01:00.0: BIT BIOS found
[   10.038741] [drm] nouveau 0000:01:00.0: Bios version 70.08.56.00
[   10.038749] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[   10.039346] [drm] nouveau 0000:01:00.0: MXM: no VBIOS data, nothing to do
[   10.039351] [drm] nouveau 0000:01:00.0: DCB version 4.0
[   10.039358] [drm] nouveau 0000:01:00.0: DCB outp 00: 02011300 00000000
[   10.039364] [drm] nouveau 0000:01:00.0: DCB outp 01: 02022362 00020010
[   10.039369] [drm] nouveau 0000:01:00.0: DCB conn 00: 00000040
[   10.039375] [drm] nouveau 0000:01:00.0: DCB conn 01: 00000100
[   10.039380] [drm] nouveau 0000:01:00.0: DCB conn 02: 00001261
[   10.039399] [drm] nouveau 0000:01:00.0: Adaptor not initialised, running VBIOS init tables.
[   10.039405] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD5E7
[   10.060627] [drm] nouveau 0000:01:00.0: 0xD591: i2c wr fail: -6
[   10.100853] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDC43
[   10.127729] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xEE49
[   10.127740] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEE4D
[   10.127805] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEF35
[   10.127811] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEF9A
[   10.154607] [TTM] Zone  kernel: Available graphics memory: 3016722 kiB
[   10.154614] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[   10.154619] [TTM] Initializing pool allocator
[   10.154630] [TTM] Initializing DMA pool allocator
[   10.154654] [drm] nouveau 0000:01:00.0: Detected 512MiB VRAM (DDR3)
[   10.154669] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[   10.154691] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[   10.166438] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   10.166440] [drm] No driver support for vblank timestamp query.
[   10.166441] [drm] nouveau 0000:01:00.0: ACPI backlight interface available, not registering our own
[   10.171824] [drm] nouveau 0000:01:00.0: 3 available performance level(s)
[   10.171826] [drm] nouveau 0000:01:00.0: 0: core 50MHz shader 101MHz memory 135MHz voltage 850mV
[   10.171828] [drm] nouveau 0000:01:00.0: 1: core 202MHz shader 405MHz memory 324MHz voltage 850mV
[   10.171831] [drm] nouveau 0000:01:00.0: 3: core 600MHz shader 1200MHz memory 900MHz voltage 950mV
[   10.171833] [drm] nouveau 0000:01:00.0: c: core 202MHz shader 405MHz memory 324MHz voltage 950mV
[   10.254598] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x1a0000, bo ffff8801a5991800
[   10.254866] fb1: nouveaufb frame buffer device
[   10.254878] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 1
[   10.254972] hda_intel: Disabling MSI
[   10.255056] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   11.076207] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.108173] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.140130] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.172087] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.188292] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input14
[   11.188623] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   11.188860] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[   11.189166] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[   12.180787] Adding 12387324k swap on /dev/sda5.  Priority:-1 extents:1 across:12387324k
[   12.212453] EXT4-fs (sda1): re-mounted. Opts: (null)
[   12.507858] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   12.865703] loop: module loaded
[   14.977822] RPC: Registered named UNIX socket transport module.
[   14.977830] RPC: Registered udp transport module.
[   14.977835] RPC: Registered tcp transport module.
[   14.977839] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   15.051772] FS-Cache: Loaded
[   15.127585] FS-Cache: Netfs 'nfs' registered for caching
[   15.145737] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   16.752319] vboxdrv: Found 4 processor cores.
[   16.752872] vboxdrv: fAsync=0 offMin=0x185 offMax=0x1507
[   16.752933] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   16.752935] vboxdrv: Successfully loaded version 4.3.14_Debian (interface 0x001a0007).
[   16.961493] vboxpci: IOMMU not found (not registered)
[   17.415716] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input18
[   20.456482] Bluetooth: RFCOMM TTY layer initialized
[   20.456487] Bluetooth: RFCOMM socket layer initialized
[   20.456488] Bluetooth: RFCOMM ver 1.11
[   20.482393] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   20.482396] Bluetooth: BNEP filters: protocol multicast
[   21.428296] lp: driver loaded but no devices found
[   21.483903] ppdev: user-space parallel port driver
[   22.971714] r8169 0000:05:00.0: firmware: agent aborted loading rtl_nic/rtl8105e-1.fw (not found?)
[   22.975292] r8169 0000:05:00.0: eth0: unable to load firmware patch rtl_nic/rtl8105e-1.fw (-2)
[   23.103502] r8169 0000:05:00.0: eth0: link down
[   23.105047] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   23.110033] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[   23.116593] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[   23.202094] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[   23.208693] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[   23.292393] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   24.753067] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[   24.755916] wlan0: authenticated
[   24.766849] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[   24.771706] wlan0: RX AssocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=5)
[   24.771714] wlan0: associated
[   24.779600] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   31.309929] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 0
[   35.883978] wlan0: no IPv6 routers present
[   71.106474] usb 2-2: new low-speed USB device number 2 using xhci_hcd
[   71.151064] usb 2-2: New USB device found, idVendor=15d9, idProduct=0a4d
[   71.151071] usb 2-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   71.151075] usb 2-2: Product:  USB OPTICAL MOUSE
[   71.151273] usb 2-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[   71.285205] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-2/2-2:1.0/input/input19
[   71.285419] generic-usb 0003:15D9:0A4D.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:0b:00.0-2/input0
[   71.285443] usbcore: registered new interface driver usbhid
[   71.285444] usbhid: USB HID core driver
[   79.483288] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[   91.316780] CPU2: Package power limit notification (total events = 1)
[   91.316784] CPU1: Package power limit notification (total events = 1)
[   91.316787] CPU3: Package power limit notification (total events = 1)
[   91.316790] CPU0: Package power limit notification (total events = 1)
[   91.318563] CPU1: Package power limit normal
[   91.318566] CPU2: Package power limit normal
[   91.318568] CPU3: Package power limit normal
[   91.318570] CPU0: Package power limit normal
[  248.633459] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 6
[  279.491518] usb 2-2: USB disconnect, device number 2
[  279.844388] usb 2-2: new low-speed USB device number 3 using xhci_hcd
[  279.892333] usb 2-2: New USB device found, idVendor=15d9, idProduct=0a4d
[  279.892339] usb 2-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  279.892343] usb 2-2: Product:  USB OPTICAL MOUSE
[  279.892504] usb 2-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[  279.915570] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-2/2-2:1.0/input/input20
[  279.915781] generic-usb 0003:15D9:0A4D.0002: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:0b:00.0-2/input0
[  284.711403] usb 2-2: reset low-speed USB device number 3 using xhci_hcd
[  284.711752] usb 2-2: Device not responding to set address.
[  284.914200] usb 2-2: Device not responding to set address.
[  285.117564] usb 2-2: device not accepting address 3, error -71
[  285.377243] usb 2-2: reset low-speed USB device number 3 using xhci_hcd
[  285.377625] usb 2-2: Device not responding to set address.
[  285.581383] usb 2-2: Device not responding to set address.
[  285.784673] usb 2-2: device not accepting address 3, error -71
[  286.044379] usb 2-2: reset low-speed USB device number 3 using xhci_hcd
[  286.044808] usb 2-2: Device not responding to set address.
[  286.248416] usb 2-2: Device not responding to set address.
[  286.451803] usb 2-2: device not accepting address 3, error -71
[  286.711515] usb 2-2: reset low-speed USB device number 3 using xhci_hcd
[  286.711989] usb 2-2: Device not responding to set address.
[  286.915558] usb 2-2: Device not responding to set address.
[  287.118939] usb 2-2: device not accepting address 3, error -71
[  287.118982] usb 2-2: USB disconnect, device number 3
[  287.216093] xhci_hcd 0000:0b:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8800bb519bc0
[  287.326696] usb 2-2: new low-speed USB device number 4 using xhci_hcd
[  287.327051] usb 2-2: Device not responding to set address.
[  287.530779] usb 2-2: Device not responding to set address.
[  287.734148] usb 2-2: device not accepting address 4, error -71
[  287.846054] usb 2-2: new low-speed USB device number 5 using xhci_hcd
[  287.846433] usb 2-2: Device not responding to set address.
[  288.050197] usb 2-2: Device not responding to set address.
[  288.253473] usb 2-2: device not accepting address 5, error -71
[  288.365339] usb 2-2: new low-speed USB device number 6 using xhci_hcd
[  288.365694] usb 2-2: Device not responding to set address.
[  288.569531] usb 2-2: Device not responding to set address.
[  288.772807] usb 2-2: device not accepting address 6, error -71
[  288.884674] usb 2-2: new low-speed USB device number 7 using xhci_hcd
[  288.885028] usb 2-2: Device not responding to set address.
[  289.088782] usb 2-2: Device not responding to set address.
[  289.292160] usb 2-2: device not accepting address 7, error -71
[  289.292223] hub 2-0:1.0: unable to enumerate USB device on port 2
[  292.176408] usb 2-2: new low-speed USB device number 8 using xhci_hcd
[  292.176756] usb 2-2: Device not responding to set address.
[  292.380553] usb 2-2: Device not responding to set address.
[  292.583937] usb 2-2: device not accepting address 8, error -71
[  292.695802] usb 2-2: new low-speed USB device number 9 using xhci_hcd
[  292.696236] usb 2-2: Device not responding to set address.
[  292.899909] usb 2-2: Device not responding to set address.
[  293.103199] usb 2-2: device not accepting address 9, error -71
[  293.215073] usb 2-2: new low-speed USB device number 10 using xhci_hcd
[  293.215423] usb 2-2: Device not responding to set address.
[  293.419191] usb 2-2: Device not responding to set address.
[  293.622528] usb 2-2: device not accepting address 10, error -71
[  293.734567] usb 2-2: new low-speed USB device number 11 using xhci_hcd
[  293.734931] usb 2-2: Device not responding to set address.
[  293.938498] usb 2-2: Device not responding to set address.
[  294.141856] usb 2-2: device not accepting address 11, error -71
[  294.141885] hub 2-0:1.0: unable to enumerate USB device on port 2
[  323.228373] usb 2-2: new low-speed USB device number 12 using xhci_hcd
[  323.228794] usb 2-2: Device not responding to set address.
[  323.432462] usb 2-2: Device not responding to set address.
[  323.635812] usb 2-2: device not accepting address 12, error -71
[  323.747637] usb 2-2: new low-speed USB device number 13 using xhci_hcd
[  323.748044] usb 2-2: Device not responding to set address.
[  323.951692] usb 2-2: Device not responding to set address.
[  324.155082] usb 2-2: device not accepting address 13, error -71
[  324.267101] usb 2-2: new low-speed USB device number 14 using xhci_hcd
[  324.267487] usb 2-2: Device not responding to set address.
[  324.471109] usb 2-2: Device not responding to set address.
[  324.674380] usb 2-2: device not accepting address 14, error -71
[  324.786228] usb 2-2: new low-speed USB device number 15 using xhci_hcd
[  324.786601] usb 2-2: Device not responding to set address.
[  324.990406] usb 2-2: Device not responding to set address.
[  325.193795] usb 2-2: device not accepting address 15, error -71
[  325.193854] hub 2-0:1.0: unable to enumerate USB device on port 2
[  391.414585] CPU1: Package power limit notification (total events = 212)
[  391.414588] CPU3: Package power limit notification (total events = 212)
[  391.414616] CPU2: Package power limit notification (total events = 212)
[  391.414619] CPU0: Package power limit notification (total events = 212)
[  391.414794] CPU1: Package power limit normal
[  391.414797] CPU3: Package power limit normal
[  391.414800] CPU2: Package power limit normal
[  391.414802] CPU0: Package power limit normal
[  428.904847] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[  429.043570] cfg80211: Calling CRDA to update world regulatory domain
[  429.059934] cfg80211: World regulatory domain updated:
[  429.059942] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  429.059950] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  429.059957] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  429.059962] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[  429.059968] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  429.059974] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  429.059980] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  429.059985] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  429.059992] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[  430.563628] PM: Syncing filesystems ... done.
[  430.564597] PM: Preparing system for mem sleep
[  430.837207] Freezing user space processes ... (elapsed 0.01 seconds) done.
[  430.853160] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[  430.869149] PM: Entering mem sleep
[  430.869289] Suspending console(s) (use no_console_suspend to debug)
[  430.869607] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[  430.869971] sd 0:0:0:0: [sda] Stopping disk
[  430.883858] [drm] nouveau 0000:01:00.0: Disabling display...
[  430.883977] [drm] nouveau 0000:01:00.0: Disabling fbcon...
[  430.883980] [drm] nouveau 0000:01:00.0: Unpinning framebuffer(s)...
[  430.884023] [drm] nouveau 0000:01:00.0: Evicting buffers...
[  430.884058] pciehp 0000:00:1c.7:pcie04: pciehp_suspend ENTRY
[  430.884578] [drm] nouveau 0000:01:00.0: Idling channels...
[  430.884767] [drm] nouveau 0000:01:00.0: Suspending GPU objects...
[  431.277997] [drm] nouveau 0000:01:00.0: And we're gone!
[  431.292581] nouveau 0000:01:00.0: power state changed by ACPI to D3
[  431.292731] PM: suspend of devices complete after 423.903 msecs
[  431.292873] pcieport 0000:00:1c.4: wake-up capability enabled by ACPI
[  431.324592] r8169 0000:05:00.0: wake-up capability enabled by ACPI
[  431.344054] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[  431.360104] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[  431.372504] PM: late suspend of devices complete after 79.871 msecs
[  431.372686] ACPI: Preparing to enter system sleep state S3
[  431.382167] PM: Saving platform NVS memory
[  431.389563] Disabling non-boot CPUs ...
[  431.492233] CPU 1 is now offline
[  431.596095] CPU 2 is now offline
[  431.699963] CPU 3 is now offline
[  431.700452] Extended CMOS year: 2000
[  431.700703] ACPI: Low-level resume complete
[  431.700744] PM: Restoring platform NVS memory
[  431.701508] Extended CMOS year: 2000
[  431.701546] Enabling non-boot CPUs ...
[  431.701665] Booting Node 0 Processor 1 APIC 0x2
[  431.701666] smpboot cpu 1: start_ip = 98000
[  431.712681] Calibrating delay loop (skipped) already calibrated this CPU
[  431.732991] NMI watchdog enabled, takes one hw-pmu counter.
[  431.733252] CPU1 is up
[  431.733363] Booting Node 0 Processor 2 APIC 0x1
[  431.733364] smpboot cpu 2: start_ip = 98000
[  431.744379] Calibrating delay loop (skipped) already calibrated this CPU
[  431.764762] NMI watchdog enabled, takes one hw-pmu counter.
[  431.765018] CPU2 is up
[  431.765185] Booting Node 0 Processor 3 APIC 0x3
[  431.765187] smpboot cpu 3: start_ip = 98000
[  431.776200] Calibrating delay loop (skipped) already calibrated this CPU
[  431.796676] NMI watchdog enabled, takes one hw-pmu counter.
[  431.796991] CPU3 is up
[  431.800936] ACPI: Waking up from system sleep state S3
[  431.822406] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[  431.825430] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[  431.826037] pcieport 0000:00:1c.4: wake-up capability disabled by ACPI
[  431.826088] PM: early resume of devices complete after 6.712 msecs
[  431.826149] i915 0000:00:02.0: setting latency timer to 64
[  431.826185] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[  431.826220] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[  431.826247] pciehp 0000:00:1c.7:pcie04: pciehp_resume ENTRY
[  431.826254] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[  431.826263] ahci 0000:00:1f.2: setting latency timer to 64
[  431.826280] [drm] nouveau 0000:01:00.0: We're back, enabling device...
[  431.826288] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[  431.826316] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[  431.826333] r8169 0000:05:00.0: wake-up capability disabled by ACPI
[  431.826367] xhci_hcd 0000:0b:00.0: setting latency timer to 64
[  431.826385] usb usb2: root hub lost power or was reset
[  431.826387] usb usb3: root hub lost power or was reset
[  431.826475] nouveau 0000:01:00.0: power state changed by ACPI to D0
[  431.826482] nouveau 0000:01:00.0: power state changed by ACPI to D0
[  431.826490] nouveau 0000:01:00.0: power state changed by ACPI to D0
[  431.826496] nouveau 0000:01:00.0: power state changed by ACPI to D0
[  431.826511] nouveau 0000:01:00.0: setting latency timer to 64
[  431.826516] [drm] nouveau 0000:01:00.0: POSTing device...
[  431.826519] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD5E7
[  431.828164] xhci_hcd 0000:0b:00.0: irq 47 for MSI/MSI-X
[  431.828169] xhci_hcd 0000:0b:00.0: irq 48 for MSI/MSI-X
[  431.828174] xhci_hcd 0000:0b:00.0: irq 49 for MSI/MSI-X
[  431.828179] xhci_hcd 0000:0b:00.0: irq 50 for MSI/MSI-X
[  431.828183] xhci_hcd 0000:0b:00.0: irq 51 for MSI/MSI-X
[  431.829445] sd 0:0:0:0: [sda] Starting disk
[  431.844619] Extended CMOS year: 2000
[  431.849476] [drm] nouveau 0000:01:00.0: 0xD591: i2c wr fail: -6
[  431.867931] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[  431.889568] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDC43
[  431.916409] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xEE49
[  431.916415] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEE4D
[  431.916471] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEF35
[  431.916472] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEF9A
[  431.936298] [drm] nouveau 0000:01:00.0: Restoring GPU objects...
[  431.959346] [drm] nouveau 0000:01:00.0: Reinitialising engines...
[  431.960047] [drm] nouveau 0000:01:00.0: Restoring mode...
[  432.084671] usb 1-1.5: reset high-speed USB device number 4 using ehci_hcd
[  432.156443] ata6: SATA link down (SStatus 0 SControl 300)
[  432.164435] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  432.176621] ata5.00: configured for UDMA/100
[  432.248479] usb 1-1.4: reset full-speed USB device number 3 using ehci_hcd
[  432.445471] btusb 1-1.4:1.0: no reset_resume for driver btusb?
[  432.445480] btusb 1-1.4:1.1: no reset_resume for driver btusb?
[  434.777062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  434.778621] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  434.780481] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[  434.780786] ata1.00: configured for UDMA/133
[  434.844622] PM: resume of devices complete after 3022.402 msecs
[  434.844922] PM: Finishing wakeup.
[  434.844923] Restarting tasks ... done.
[  434.854828] video LNXVIDEO:00: Restoring backlight state
[  434.855080] video LNXVIDEO:01: Restoring backlight state
[  434.956802] usb 2-2: new low-speed USB device number 16 using xhci_hcd
[  434.957225] usb 2-2: Device not responding to set address.
[  435.160863] usb 2-2: Device not responding to set address.
[  435.364283] usb 2-2: device not accepting address 16, error -71
[  435.419012] r8169 0000:05:00.0: eth0: link down
[  435.419911] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  435.421132] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[  435.427739] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[  435.476095] usb 2-2: new low-speed USB device number 17 using xhci_hcd
[  435.476449] usb 2-2: Device not responding to set address.
[  435.523931] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  435.523938] device wlan0 entered promiscuous mode
[  435.680312] usb 2-2: Device not responding to set address.
[  435.883569] usb 2-2: device not accepting address 17, error -71
[  435.995397] usb 2-2: new low-speed USB device number 18 using xhci_hcd
[  435.995742] usb 2-2: Device not responding to set address.
[  436.060658] atkbd serio0: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[  436.060662] atkbd serio0: Use 'setkeycodes e00d <keycode>' to make it known.
[  436.199463] usb 2-2: Device not responding to set address.
[  436.402943] usb 2-2: device not accepting address 18, error -71
[  436.513533] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[  436.514753] usb 2-2: new low-speed USB device number 19 using xhci_hcd
[  436.515123] usb 2-2: Device not responding to set address.
[  436.516397] wlan0: authenticated
[  436.516859] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[  436.520191] wlan0: RX AssocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=5)
[  436.520202] wlan0: associated
[  436.524124] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  436.718985] usb 2-2: Device not responding to set address.
[  436.922208] usb 2-2: device not accepting address 19, error -71
[  436.922260] hub 2-0:1.0: unable to enumerate USB device on port 2
[  436.994443] usb 4-1.6: new high-speed USB device number 4 using ehci_hcd
[  437.342681] usb 4-1.6: New USB device found, idVendor=0bda, idProduct=0138
[  437.342694] usb 4-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  437.342703] usb 4-1.6: Product: USB2.0-CRW
[  437.342710] usb 4-1.6: Manufacturer: Generic
[  437.342716] usb 4-1.6: SerialNumber: 20090516388200000
[  437.367554] scsi7 : usb-storage 4-1.6:1.0
[  437.368484] usb 4-1.6: USB disconnect, device number 4
[  440.042280] usb 2-2: new low-speed USB device number 20 using xhci_hcd
[  440.042703] usb 2-2: Device not responding to set address.
[  440.246396] usb 2-2: Device not responding to set address.
[  440.449732] usb 2-2: device not accepting address 20, error -71
[  440.561590] usb 2-2: new low-speed USB device number 21 using xhci_hcd
[  440.561969] usb 2-2: Device not responding to set address.
[  440.765796] usb 2-2: Device not responding to set address.
[  440.969068] usb 2-2: device not accepting address 21, error -71
[  441.080907] usb 2-2: new low-speed USB device number 22 using xhci_hcd
[  441.081363] usb 2-2: Device not responding to set address.
[  441.285114] usb 2-2: Device not responding to set address.
[  441.488345] usb 2-2: device not accepting address 22, error -71
[  441.600272] usb 2-2: new low-speed USB device number 23 using xhci_hcd
[  441.600738] usb 2-2: Device not responding to set address.
[  441.804491] usb 2-2: Device not responding to set address.
[  442.007651] usb 2-2: device not accepting address 23, error -71
[  442.007712] hub 2-0:1.0: unable to enumerate USB device on port 2
[  446.889342] wlan0: no IPv6 routers present
[  461.766168] usb 2-2: new low-speed USB device number 24 using xhci_hcd
[  461.810773] usb 2-2: New USB device found, idVendor=15d9, idProduct=0a4d
[  461.810783] usb 2-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  461.810789] usb 2-2: Product:  USB OPTICAL MOUSE
[  461.811062] usb 2-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[  461.831130] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-2/2-2:1.0/input/input21
[  461.831615] generic-usb 0003:15D9:0A4D.0003: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:0b:00.0-2/input0
[  481.750356] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[  481.760820] cfg80211: Calling CRDA to update world regulatory domain
[  481.764755] cfg80211: World regulatory domain updated:
[  481.764758] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  481.764760] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  481.764763] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  481.764765] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[  481.764767] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  481.764769] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  481.764771] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  481.764773] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  481.764775] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[  485.067272] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[  485.070150] wlan0: authenticated
[  485.070524] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[  485.077935] wlan0: RX ReassocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=5)
[  485.077946] wlan0: associated
[  495.953859] wlan0: no IPv6 routers present
[  530.688532] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[  530.699148] cfg80211: Calling CRDA to update world regulatory domain
[  530.705537] cfg80211: World regulatory domain updated:
[  530.705543] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  530.705550] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  530.705555] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  530.705559] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[  530.705564] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  530.705569] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  530.705573] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[  530.705578] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[  530.705583] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[  534.010100] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[  534.013087] wlan0: authenticated
[  534.013267] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[  534.016464] wlan0: RX ReassocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=5)
[  534.016466] wlan0: associated
[  544.778664] wlan0: no IPv6 routers present
[  549.227261] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 0
[  745.746271] CPU3: Package power limit notification (total events = 309)
[  745.746276] CPU0: Package power limit notification (total events = 309)
[  745.746279] CPU2: Package power limit notification (total events = 309)
[  745.746282] CPU1: Package power limit notification (total events = 309)
[  745.747045] CPU1: Package power limit normal
[  745.747048] CPU2: Package power limit normal
[  745.747050] CPU3: Package power limit normal
[  745.747053] CPU0: Package power limit normal
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח IIאורח · ·
 

הודעה פורסם: 29/11/2014 - 19:47
נושא ההודעה: יש מצב שחברת HOT הואילה בטובה לעדכן לך את המודם

אחרי שהתלוננתי על ניתוקים, וכן הם זיהו שיש לי ניתוקים
נכון לעד לפני שעה כם הרכיבים האלחוטיים (טלפונים, ניידים ועוד) הפסיקו לעבוד

פתאום הופיעה אצלי בבית רשת חדשה, המגביר טווח לא הצליח להתחבר לרשת,
ניסיתי להכנס ל HOTBOX עם המשתמש והסיסמא שלי המוכרים - ללא הצלחה.

נכנסתי עם ברירת המחדל שלהם, הגדרתי מה שטעון הגדרה והכל חזר לעבודה.

יש מצב שזה הרבה יותר פשוט ממה שנראה
וכן זו חוצפה של חברת HOT.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 29/11/2014 - 20:16
נושא ההודעה:

ניסיתי גם את מה שאתה אומר והבאתי אפילו טכנאי פעמיים ואיפסתי את הראוטר ועדיין

עכשיו אפילו יש לי בעיה חדשה העכבר usb שלי נתקע כל הזמן
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 30/11/2014 - 09:03
נושא ההודעה:

Anonymous :
ניסיתי גם את מה שאתה אומר והבאתי אפילו טכנאי פעמיים ואיפסתי את הראוטר ועדיין

עכשיו אפילו יש לי בעיה חדשה העכבר usb שלי נתקע כל הזמן


לגבי העכבר יש לך בעיית ב usb תראה:
קוד:


[  293.419191] usb 2-2: Device not responding to set address.

[  293.622528] usb 2-2: device not accepting address 10, error -71

[  293.734567] usb 2-2: new low-speed USB device number 11 using xhci_hcd

[  293.734931] usb 2-2: Device not responding to set address.

[  293.938498] usb 2-2: Device not responding to set address.

[  294.141856] usb 2-2: device not accepting address 11, error -71

[  294.141885] hub 2-0:1.0: unable to enumerate USB device on port 2

[  323.228373] usb 2-2: new low-speed USB device number 12 using xhci_hcd

[  323.228794] usb 2-2: Device not responding to set address.

[  323.432462] usb 2-2: Device not responding to set address.

[  323.635812] usb 2-2: device not accepting address 12, error -71

[  323.747637] usb 2-2: new low-speed USB device number 13 using xhci_hcd

[  323.748044] usb 2-2: Device not responding to set address.

[  323.951692] usb 2-2: Device not responding to set address.

[  324.155082] usb 2-2: device not accepting address 13, error -71

[  324.267101] usb 2-2: new low-speed USB device number 14 using xhci_hcd

[  324.267487] usb 2-2: Device not responding to set address.

[  324.471109] usb 2-2: Device not responding to set address.

[  324.674380] usb 2-2: device not accepting address 14, error -71

[  324.786228] usb 2-2: new low-speed USB device number 15 using xhci_hcd

[  324.786601] usb 2-2: Device not responding to set address.

[  324.990406] usb 2-2: Device not responding to set address.

[  325.193795] usb 2-2: device not accepting address 15, error -71
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
צפריראורח · ·
 

הודעה פורסם: 30/11/2014 - 10:30
נושא ההודעה: Re: יש מצב שחברת HOT הואילה בטובה לעדכן לך את המודם

אורח II :
אחרי שהתלוננתי על ניתוקים, וכן הם זיהו שיש לי ניתוקים
נכון לעד לפני שעה כם הרכיבים האלחוטיים (טלפונים, ניידים ועוד) הפסיקו לעבוד

נפריד כאן בין שתי בעיות שונות: התחברות לנתב ברשת המקומית והתחברות ממנו לשאר האינטרנט (או ליתר דיוק: התחברות לספק החיבור. החיבור מספק החיבור לשאר האינטרנט עובד כמעט תמיד ולא תלוי בנו).

לפי הדיווח שכאן, מחשבים אחרים בבית מצליחים להתחבר לאינטרנט דרך אותו נתב. כמוכן אותו מחשב מצליח להתחבר בחיבור קווי. לכן לא נראה שיש בעיה בחיבור בין הנתב לספק.

השלב הבא: מה בדיוק עובד ומה לא עובד. מה הפלט של הפקודות הבאות:
/sbin/ifconfig
nm-tool

לפי הפלט של dmesg נראה שחיבור הרשת עובד באופן כללי בסדר. אז משהו לא תקין ברמה גבוהה יותר.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 30/11/2014 - 11:15
נושא ההודעה:

מה רמת הקליטה?
כתבת שאתה משתמש במגביר טווח: מאיזה סוג הוא? באיזה טווח אתה נמצא ממנו? האם אתה בממ"ד?
בגדול, זה נראה כמו בעיית קליטה ולא יותר.
האם ניסית להתקרב לנתב?
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 30/11/2014 - 13:01
12 נושא ההודעה:

אורח II :
יש מצב שזה הרבה יותר פשוט ממה שנראה
וכן זו חוצפה של חברת HOT.


HOT זו חברה מצוינת. למה להשמיץ?
הבעיה היא בך.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אלכס___אורח · ·
 

הודעה פורסם: 30/11/2014 - 20:41
נושא ההודעה:

שלום.
לפ הפלט שהבאת פה:
קוד:
[  428.904847] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)


לפי הפלט נראה כמו שאתה משתמש ברשת מוצפנת. אים כן באיזה פרוטקל הצפנה אתה משתמש?

המחשב שלך מנתק את עצמו מהרשת(נראה כמו שמערכת שלך לא סומכת על אמינות של הרשת שהיא נמצאת בה).

זה יכול לקרות מכמה סיבות אפשרייות כמו:
1. יש מספר שרותים(תוכנות שרצות ברקה לצורך בקרה ותפעול) שמתנגשים אחת עם השני.
קוד:
ls /etc/init.d  <- בפקודה הזו תיתן את כל השרותים שמותקנים לך על המחשב

+ את הפלטים שצפריר ביקש.
2. בעיות ביציבות קליטת האותות ה WIFI.

בנוסף תספק בבקשה:
1. לפי איזה מדריך פעלתה כדי להשתמש ב WIFI.
2. מה התקנתה כדי להשתמש בכרטיס הרשת העל חוטי.
3. האם זה היה שדרוג מערכת הפעלה מגירסה קודמת או התקנה נקיה מחדש.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 30/11/2014 - 21:14
נושא ההודעה: Re: יש מצב שחברת HOT הואילה בטובה לעדכן לך את המודם

צפריר :
אורח II :
אחרי שהתלוננתי על ניתוקים, וכן הם זיהו שיש לי ניתוקים
נכון לעד לפני שעה כם הרכיבים האלחוטיים (טלפונים, ניידים ועוד) הפסיקו לעבוד

נפריד כאן בין שתי בעיות שונות: התחברות לנתב ברשת המקומית והתחברות ממנו לשאר האינטרנט (או ליתר דיוק: התחברות לספק החיבור. החיבור מספק החיבור לשאר האינטרנט עובד כמעט תמיד ולא תלוי בנו).

לפי הדיווח שכאן, מחשבים אחרים בבית מצליחים להתחבר לאינטרנט דרך אותו נתב. כמוכן אותו מחשב מצליח להתחבר בחיבור קווי. לכן לא נראה שיש בעיה בחיבור בין הנתב לספק.

השלב הבא: מה בדיוק עובד ומה לא עובד. מה הפלט של הפקודות הבאות:
/sbin/ifconfig
nm-tool

לפי הפלט של dmesg נראה שחיבור הרשת עובד באופן כללי בסדר. אז משהו לא תקין ברמה גבוהה יותר.


תיקון טעות שאני גולש דרך הפלא זה לא קווי זה אל חוטי

את הבעיה של העכבר פתרתי כאן http://forums.debian.net/viewtopic.php?f=7&t=103447
וזה גם עזר לי לניתוקים אבל מישום מה האינטרנט ממש איטי





אלכס:
הפרוטוקול הצפנה של wapa/wpa2 איך הבנת שזה מוצפן?

זה מה שאני מביא את ls /etc/init.d
קוד:
acpid           bootlogs                cups         keyboard-setup         mountkernfs.sh         pulseaudio  rsync              udev-mtab
acpi-fakekey    bootmisc.sh             dbus         killprocs              mountnfs-bootclean.sh  qemu-kvm    rsyslog            umountfs
acpi-support    checkfs.sh              exim4        kmod                   mountnfs.sh            rc          saned              umountnfs.sh
alsa-utils      checkroot-bootclean.sh  gdm3         laptop-mode            mtab.sh                rc.local    sendsigs           umountroot
anacron         checkroot.sh            halt         minissdpd              networking             rcS         single             unattended-upgrades
atd             console-setup           hdparm       motd                   network-manager        README      skeleton           urandom
avahi-daemon    cron                    hostname.sh  mountall-bootclean.sh  nfs-common             reboot      speech-dispatcher  virtualbox
binfmt-support  cryptdisks              hwclock.sh   mountall.sh            pppd-dns               rmnologin   sudo               x11-common
bluetooth       cryptdisks-early        kbd          mountdevsubfs.sh       procps                 rpcbind     udev



ההתקנה הייתה נקיה הכל מחדש
עבדתי לפי המדריך הזה https://wiki.debian.org/iwlwifi


לאורחים האחרים אני לא משתמש במגבר ולא נמצא בבמ"ד שיהיה לי win קלטתי מצויין מאותו מקום



הפקודות sbin/ifconfig


קוד:
rbg@rbgcom:~$ /sbin/ifconfig
eth0      Link encap:Ethernet  HWaddr 24:b6:fd:29:83:34 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:46 Base address:0xa000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 B)  TX bytes:480 (480.0 B)

wlan0     Link encap:Ethernet  HWaddr 4c:eb:42:51:5b:21 
          inet addr:192.168.1.17  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::4eeb:42ff:fe51:5b21/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:56670 errors:0 dropped:0 overruns:0 frame:0
          TX packets:15797 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:82065777 (78.2 MiB)  TX bytes:1694548 (1.6 MiB)


הפקודה nm-tool

קוד:
NetworkManager Tool

State: connected (global)

- Device: wlan0  [Auto moshe] --------------------------------------------------
  Type:              802.11 WiFi
  Driver:            iwlwifi
  State:             connected
  Default:           yes
  HW Address:        4C:EB:42:51:5B:21

  Capabilities:
    Speed:           72 Mb/s

  Wireless Properties
    WEP Encryption:  yes
    WPA Encryption:  yes
    WPA2 Encryption: yes

  Wireless Access Points (* = current AP)
    jerusalem10:     Infra, 1C:7E:E5:DA:5E:0B, Freq 2457 MHz, Rate 54 Mb/s, Strength 42 WPA2
    sweex:           Infra, 00:16:0A:0F:9E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 67 WEP
    *moshe:          Infra, C0:AC:54:F7:23:85, Freq 2462 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2

  IPv4 Settings:
    Address:         192.168.1.17
    Prefix:          24 (255.255.255.0)
    Gateway:         192.168.1.1

    DNS:             213.57.2.5
    DNS:             213.57.22.5


- Device: eth0 -----------------------------------------------------------------
  Type:              Wired
  Driver:            r8169
  State:             unavailable
  Default:           no
  HW Address:        24:B6:FD:29:83:34

  Capabilities:
    Carrier Detect:  yes

  Wired Properties
    Carrier:         off
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אלכס___אורח · ·
 

הודעה פורסם: 01/12/2014 - 00:12
נושא ההודעה:

שלום

1. לפי הפלטים שבאתה אני לא רואה שרותים שאמורים לעשות בעיות.
2. עדיין לא אמרתה איך פעלתה לפי המדריך ומה התקנתה. אם התקנתה את כל מה שמופיעה שם ללא הבחנה. אני לא אהיה מופתע שיש בעיות.

בדקתי מה קוד 3 אומר, פה:
קוד:
http://www.aboutcher.co.uk/2012/07/linux-wifi-deauthenticated-reason-codes/
"Deauthenticated because sending STA is leaving (or has left) IBSS or ESS    The access point went offline, deauthenticating the client."


המסכנה שלי כנראה שדביאן לא מגדיר את המיקום אוטומטית:

קוד:
iw reg get    <- לבדיקת אזור וטווחי הטדרים לפולה
iw reg set IL <- להגדרת אזור וטווחי הטדרים לפולה ישראלים
iw reg get    <- לבדיקה חוזרת


אים זה פתר את הבעיה בשבילך אשמח לדעת.
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 01/12/2014 - 20:22
נושא ההודעה:

אוקי אני התקנתי את הדייבר ככה אני יודע שיש לי דיביאן 7 ולכן

שמתי את זה ב/etc/apt/sources.list

deb http://http.debian.net/debian/ wheezy main contrib non-free


ואז שמתי את זה בטרמינטל
apt-get update && apt-get install firmware-iwlwifi
modprobe -r iwlwifi ; modprobe iwlwifi

וזהו

לגבי הגדרת תדרים אוקי לא היה לי מוגדר אז אני אעדכן בהמשך האם זה עזר

תודה בכל מקרה
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 07/12/2014 - 19:53
נושא ההודעה:

עדיין עושה בעיות כבר לא מתנתק אבל הרבה נתקע באמצע



קוד:
[   10.559347] [drm] nouveau 0000:01:00.0: Bios version 70.08.56.00
[   10.559355] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[   10.559937] [drm] nouveau 0000:01:00.0: MXM: no VBIOS data, nothing to do
[   10.559942] [drm] nouveau 0000:01:00.0: DCB version 4.0
[   10.559948] [drm] nouveau 0000:01:00.0: DCB outp 00: 02011300 00000000
[   10.559954] [drm] nouveau 0000:01:00.0: DCB outp 01: 02022362 00020010
[   10.559960] [drm] nouveau 0000:01:00.0: DCB conn 00: 00000040
[   10.559966] [drm] nouveau 0000:01:00.0: DCB conn 01: 00000100
[   10.559971] [drm] nouveau 0000:01:00.0: DCB conn 02: 00001261
[   10.559990] [drm] nouveau 0000:01:00.0: Adaptor not initialised, running VBIOS init tables.
[   10.559996] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD5E7
[   10.581247] [drm] nouveau 0000:01:00.0: 0xD591: i2c wr fail: -6
[   10.621476] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDC43
[   10.648355] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xEE49
[   10.648366] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEE4D
[   10.648431] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEF35
[   10.648437] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEF9A
[   10.675249] [TTM] Zone  kernel: Available graphics memory: 3016722 kiB
[   10.675256] [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
[   10.675261] [TTM] Initializing pool allocator
[   10.675273] [TTM] Initializing DMA pool allocator
[   10.675297] [drm] nouveau 0000:01:00.0: Detected 512MiB VRAM (DDR3)
[   10.675311] mtrr: type mismatch for e0000000,10000000 old: write-back new: write-combining
[   10.675334] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[   10.687238] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   10.687239] [drm] No driver support for vblank timestamp query.
[   10.687241] [drm] nouveau 0000:01:00.0: ACPI backlight interface available, not registering our own
[   10.692628] [drm] nouveau 0000:01:00.0: 3 available performance level(s)
[   10.692631] [drm] nouveau 0000:01:00.0: 0: core 50MHz shader 101MHz memory 135MHz voltage 850mV
[   10.692633] [drm] nouveau 0000:01:00.0: 1: core 202MHz shader 405MHz memory 324MHz voltage 850mV
[   10.692635] [drm] nouveau 0000:01:00.0: 3: core 600MHz shader 1200MHz memory 900MHz voltage 950mV
[   10.692637] [drm] nouveau 0000:01:00.0: c: core 202MHz shader 405MHz memory 324MHz voltage 950mV
[   10.774650] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x1a0000, bo ffff8801a59a8000
[   10.774920] fb1: nouveaufb frame buffer device
[   10.774932] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 1
[   10.775022] hda_intel: Disabling MSI
[   10.775116] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[   11.591539] HDMI status: Codec=0 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.623497] HDMI status: Codec=1 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.655457] HDMI status: Codec=2 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.687412] HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0
[   11.703628] input: HDA NVidia HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input15
[   11.703960] input: HDA NVidia HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input16
[   11.704198] input: HDA NVidia HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input17
[   11.704508] input: HDA NVidia HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input18
[   12.622967] Adding 12387324k swap on /dev/sda5.  Priority:-1 extents:1 across:12387324k
[   12.654306] EXT4-fs (sda1): re-mounted. Opts: (null)
[   12.942776] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   13.259107] loop: module loaded
[   15.335821] RPC: Registered named UNIX socket transport module.
[   15.335823] RPC: Registered udp transport module.
[   15.335824] RPC: Registered tcp transport module.
[   15.335825] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   15.395639] FS-Cache: Loaded
[   15.467331] FS-Cache: Netfs 'nfs' registered for caching
[   15.480926] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   17.048671] vboxdrv: Found 4 processor cores.
[   17.048801] vboxdrv: fAsync=0 offMin=0x1b5 offMax=0xef8
[   17.048842] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[   17.048843] vboxdrv: Successfully loaded version 4.3.14_Debian (interface 0x001a0007).
[   17.140476] vboxpci: IOMMU not found (not registered)
[   17.783792] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input19
[   19.772705] Bluetooth: RFCOMM TTY layer initialized
[   19.772719] Bluetooth: RFCOMM socket layer initialized
[   19.772724] Bluetooth: RFCOMM ver 1.11
[   19.995302] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   19.995304] Bluetooth: BNEP filters: protocol multicast
[   20.924503] lp: driver loaded but no devices found
[   20.988483] ppdev: user-space parallel port driver
[   22.223406] r8169 0000:05:00.0: firmware: agent aborted loading rtl_nic/rtl8105e-1.fw (not found?)
[   22.224367] r8169 0000:05:00.0: eth0: unable to load firmware patch rtl_nic/rtl8105e-1.fw (-2)
[   22.344530] r8169 0000:05:00.0: eth0: link down
[   22.346084] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.351232] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[   22.357803] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[   22.442787] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[   22.449347] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[   22.540698] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   23.899088] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[   23.901924] wlan0: authenticated
[   23.906320] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[   23.911196] wlan0: RX AssocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=4)
[   23.911199] wlan0: associated
[   23.928502] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   25.509934] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,user_xattr,barrier=1,data=ordered,commit=600
[   34.549714] wlan0: no IPv6 routers present
[   70.339280] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[   70.447622] cfg80211: Calling CRDA to update world regulatory domain
[   70.456500] cfg80211: World regulatory domain updated:
[   70.456509] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   70.456516] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   70.456523] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   70.456529] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[   70.456534] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[   70.456540] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[   70.456546] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[   70.456552] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[   70.456558] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[   73.586104] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[   73.589061] wlan0: authenticated
[   73.589646] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[   73.593028] wlan0: RX ReassocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=4)
[   73.593038] wlan0: associated
[   84.565032] wlan0: no IPv6 routers present
[  130.286660] usb 4-1.2: USB disconnect, device number 3
[  130.546785] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[  130.553686] usb 4-1.2: new low-speed USB device number 5 using ehci_hcd
[  130.649156] usb 4-1.2: New USB device found, idVendor=15d9, idProduct=0a4d
[  130.649160] usb 4-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  130.649162] usb 4-1.2: Product:  USB OPTICAL MOUSE
[  130.650706] NMI watchdog enabled, takes one hw-pmu counter.
[  130.650733] NMI watchdog enabled, takes one hw-pmu counter.
[  130.650760] NMI watchdog enabled, takes one hw-pmu counter.
[  130.650780] NMI watchdog enabled, takes one hw-pmu counter.
[  130.651689] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/input/input20
[  130.651813] generic-usb 0003:15D9:0A4D.0002: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.2/input0
[  130.893182] xhci_hcd 0000:0b:00.0: setting latency timer to 64
[  131.657987] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,user_xattr,barrier=1,data=ordered,commit=0
[  134.390437] gc-watchdog[5128] trap int3 ip:7f53ba8cc491 sp:7f53904e1690 error:0
[  441.032373] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 6
[ 5119.947298] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 0
[ 7641.194051] warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
[ 7870.462117] CPU3: Package power limit notification (total events = 1)
[ 7870.462121] CPU1: Package power limit notification (total events = 1)
[ 7870.462126] CPU2: Package power limit notification (total events = 1)
[ 7870.462129] CPU0: Package power limit notification (total events = 1)
[ 7870.473001] CPU3: Package power limit normal
[ 7870.473005] CPU0: Package power limit normal
[ 7870.473009] CPU1: Package power limit normal
[ 7870.473012] CPU2: Package power limit normal
[ 8044.983120] usb 4-1.2: USB disconnect, device number 5
[ 8049.833287] usb 2-2: new low-speed USB device number 2 using xhci_hcd
[ 8049.877521] usb 2-2: New USB device found, idVendor=15d9, idProduct=0a4d
[ 8049.877531] usb 2-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 8049.877537] usb 2-2: Product:  USB OPTICAL MOUSE
[ 8049.877915] usb 2-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 8049.898954] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-2/2-2:1.0/input/input21
[ 8049.899465] generic-usb 0003:15D9:0A4D.0003: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:0b:00.0-2/input0
[11315.246376] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[11315.407651] cfg80211: Calling CRDA to update world regulatory domain
[11315.414160] cfg80211: World regulatory domain updated:
[11315.414170] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[11315.414180] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[11315.414188] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[11315.414197] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[11315.414206] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[11315.414215] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[11315.414224] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[11315.414232] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[11315.414241] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[11316.736452] PM: Syncing filesystems ... done.
[11316.737787] PM: Preparing system for mem sleep
[11317.033337] Freezing user space processes ... (elapsed 0.01 seconds) done.
[11317.049269] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[11317.065256] PM: Entering mem sleep
[11317.065380] Suspending console(s) (use no_console_suspend to debug)
[11317.065766] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[11317.066091] sd 0:0:0:0: [sda] Stopping disk
[11317.079089] [drm] nouveau 0000:01:00.0: Disabling display...
[11317.079208] [drm] nouveau 0000:01:00.0: Disabling fbcon...
[11317.079211] [drm] nouveau 0000:01:00.0: Unpinning framebuffer(s)...
[11317.079253] [drm] nouveau 0000:01:00.0: Evicting buffers...
[11317.079280] pciehp 0000:00:1c.7:pcie04: pciehp_suspend ENTRY
[11317.079798] [drm] nouveau 0000:01:00.0: Idling channels...
[11317.079940] [drm] nouveau 0000:01:00.0: Suspending GPU objects...
[11317.411075] [drm] nouveau 0000:01:00.0: And we're gone!
[11317.424777] nouveau 0000:01:00.0: power state changed by ACPI to D3
[11317.464687] PM: suspend of devices complete after 399.728 msecs
[11317.464860] pcieport 0000:00:1c.4: wake-up capability enabled by ACPI
[11317.496729] r8169 0000:05:00.0: wake-up capability enabled by ACPI
[11317.516231] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[11317.532279] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[11317.544640] PM: late suspend of devices complete after 80.046 msecs
[11317.544814] ACPI: Preparing to enter system sleep state S3
[11317.554223] PM: Saving platform NVS memory
[11317.561843] Disabling non-boot CPUs ...
[11317.664368] CPU 1 is now offline
[11317.768235] CPU 2 is now offline
[11317.872094] CPU 3 is now offline
[11317.872567] Extended CMOS year: 2000
[11317.872831] ACPI: Low-level resume complete
[11317.872872] PM: Restoring platform NVS memory
[11317.873651] Extended CMOS year: 2000
[11317.873688] Enabling non-boot CPUs ...
[11317.873810] Booting Node 0 Processor 1 APIC 0x2
[11317.873812] smpboot cpu 1: start_ip = 98000
[11317.884826] Calibrating delay loop (skipped) already calibrated this CPU
[11317.905140] NMI watchdog enabled, takes one hw-pmu counter.
[11317.905400] CPU1 is up
[11317.905504] Booting Node 0 Processor 2 APIC 0x1
[11317.905505] smpboot cpu 2: start_ip = 98000
[11317.916521] Calibrating delay loop (skipped) already calibrated this CPU
[11317.936898] NMI watchdog enabled, takes one hw-pmu counter.
[11317.937149] CPU2 is up
[11317.937258] Booting Node 0 Processor 3 APIC 0x3
[11317.937260] smpboot cpu 3: start_ip = 98000
[11317.948273] Calibrating delay loop (skipped) already calibrated this CPU
[11317.968726] NMI watchdog enabled, takes one hw-pmu counter.
[11317.968973] CPU3 is up
[11317.972879] ACPI: Waking up from system sleep state S3
[11317.994488] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[11317.997450] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[11317.998058] pcieport 0000:00:1c.4: wake-up capability disabled by ACPI
[11317.998113] PM: early resume of devices complete after 6.762 msecs
[11317.998199] i915 0000:00:02.0: setting latency timer to 64
[11317.998220] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[11317.998223] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[11317.998280] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[11317.998282] pciehp 0000:00:1c.7:pcie04: pciehp_resume ENTRY
[11317.998304] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[11317.999207] ahci 0000:00:1f.2: setting latency timer to 64
[11317.999217] [drm] nouveau 0000:01:00.0: We're back, enabling device...
[11318.000204] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[11318.000234] r8169 0000:05:00.0: wake-up capability disabled by ACPI
[11318.000262] xhci_hcd 0000:0b:00.0: setting latency timer to 64
[11318.000283] usb usb2: root hub lost power or was reset
[11318.000285] usb usb3: root hub lost power or was reset
[11318.000670] xhci_hcd 0000:0b:00.0: irq 46 for MSI/MSI-X
[11318.000673] xhci_hcd 0000:0b:00.0: irq 47 for MSI/MSI-X
[11318.000677] xhci_hcd 0000:0b:00.0: irq 48 for MSI/MSI-X
[11318.000680] xhci_hcd 0000:0b:00.0: irq 49 for MSI/MSI-X
[11318.000683] xhci_hcd 0000:0b:00.0: irq 50 for MSI/MSI-X
[11318.000860] nouveau 0000:01:00.0: power state changed by ACPI to D0
[11318.000866] nouveau 0000:01:00.0: power state changed by ACPI to D0
[11318.000872] nouveau 0000:01:00.0: power state changed by ACPI to D0
[11318.000876] nouveau 0000:01:00.0: power state changed by ACPI to D0
[11318.000883] nouveau 0000:01:00.0: setting latency timer to 64
[11318.000888] [drm] nouveau 0000:01:00.0: POSTing device...
[11318.000890] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD5E7
[11318.013036] sd 0:0:0:0: [sda] Starting disk
[11318.023456] [drm] nouveau 0000:01:00.0: 0xD591: i2c wr fail: -6
[11318.040676] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[11318.063441] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDC43
[11318.090264] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xEE49
[11318.090269] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEE4D
[11318.090321] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEF35
[11318.090323] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEF9A
[11318.110147] [drm] nouveau 0000:01:00.0: Restoring GPU objects...
[11318.133152] [drm] nouveau 0000:01:00.0: Reinitialising engines...
[11318.133633] [drm] nouveau 0000:01:00.0: Restoring mode...
[11318.252837] usb 1-1.4: reset full-speed USB device number 3 using ehci_hcd
[11318.332607] ata6: SATA link down (SStatus 0 SControl 300)
[11318.340606] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[11318.347670] btusb 1-1.4:1.0: no reset_resume for driver btusb?
[11318.347679] btusb 1-1.4:1.1: no reset_resume for driver btusb?
[11318.352776] ata5.00: configured for UDMA/100
[11318.416653] usb 1-1.5: reset high-speed USB device number 4 using ehci_hcd
[11318.768128] usb 2-2: reset low-speed USB device number 2 using xhci_hcd
[11318.797951] xhci_hcd 0000:0b:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880184c5bf00
[11318.797977] usb 2-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[11320.921255] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[11320.922779] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[11320.924641] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[11320.924945] ata1.00: configured for UDMA/133
[11320.988479] PM: resume of devices complete after 2994.202 msecs
[11320.988756] PM: Finishing wakeup.
[11320.988757] Restarting tasks ... done.
[11320.994072] video LNXVIDEO:00: Restoring backlight state
[11320.994212] video LNXVIDEO:01: Restoring backlight state
[11321.065419] usb 4-1.6: new high-speed USB device number 6 using ehci_hcd
[11321.408972] usb 4-1.6: New USB device found, idVendor=0bda, idProduct=0138
[11321.408977] usb 4-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11321.408980] usb 4-1.6: Product: USB2.0-CRW
[11321.408982] usb 4-1.6: Manufacturer: Generic
[11321.408984] usb 4-1.6: SerialNumber: 20090516388200000
[11321.433935] scsi7 : usb-storage 4-1.6:1.0
[11321.582472] usb 4-1.6: USB disconnect, device number 6
[11321.743098] r8169 0000:05:00.0: eth0: link down
[11321.744754] ADDRCONF(NETDEV_UP): eth0: link is not ready
[11321.747978] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[11321.754593] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[11321.875392] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[11321.875412] device wlan0 entered promiscuous mode
[11322.836172] atkbd serio0: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[11322.836185] atkbd serio0: Use 'setkeycodes e00d <keycode>' to make it known.
[11322.888644] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[11322.891474] wlan0: authenticated
[11322.892093] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[11322.895317] wlan0: RX AssocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=4)
[11322.895327] wlan0: associated
[11322.899523] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[11333.816515] wlan0: no IPv6 routers present
[11356.657280] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 0
[12959.091383] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 6
[17497.157952] usb 2-2: USB disconnect, device number 2
[17502.541920] usb 4-1.2: new low-speed USB device number 7 using ehci_hcd
[17502.638054] usb 4-1.2: New USB device found, idVendor=15d9, idProduct=0a4d
[17502.638064] usb 4-1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[17502.638070] usb 4-1.2: Product:  USB OPTICAL MOUSE
[17502.641464] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.2/4-1.2:1.0/input/input22
[17502.641935] generic-usb 0003:15D9:0A4D.0004: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:1d.0-1.2/input0
[20687.373670] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[20687.380253] cfg80211: Calling CRDA to update world regulatory domain
[20687.391167] cfg80211: World regulatory domain updated:
[20687.391178] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[20687.391189] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[20687.391198] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[20687.391207] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[20687.391216] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[20687.391225] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[20687.391234] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[20687.391243] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[20687.391252] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[20687.392961] device wlan0 left promiscuous mode
[20688.543658] PM: Syncing filesystems ... done.
[20688.545749] PM: Preparing system for mem sleep
[20688.774530] Freezing user space processes ... (elapsed 0.01 seconds) done.
[20688.790445] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[20688.806430] PM: Entering mem sleep
[20688.806558] Suspending console(s) (use no_console_suspend to debug)
[20688.806925] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[20688.807283] sd 0:0:0:0: [sda] Stopping disk
[20688.820335] [drm] nouveau 0000:01:00.0: Disabling display...
[20688.820441] [drm] nouveau 0000:01:00.0: Disabling fbcon...
[20688.820445] [drm] nouveau 0000:01:00.0: Unpinning framebuffer(s)...
[20688.820490] pciehp 0000:00:1c.7:pcie04: pciehp_suspend ENTRY
[20688.820493] [drm] nouveau 0000:01:00.0: Evicting buffers...
[20688.821142] [drm] nouveau 0000:01:00.0: Idling channels...
[20688.821282] [drm] nouveau 0000:01:00.0: Suspending GPU objects...
[20689.152034] [drm] nouveau 0000:01:00.0: And we're gone!
[20689.165955] nouveau 0000:01:00.0: power state changed by ACPI to D3
[20689.218004] PM: suspend of devices complete after 411.887 msecs
[20689.218147] pcieport 0000:00:1c.4: wake-up capability enabled by ACPI
[20689.249890] r8169 0000:05:00.0: wake-up capability enabled by ACPI
[20689.269840] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI
[20689.289917] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI
[20689.305798] PM: late suspend of devices complete after 87.901 msecs
[20689.305973] ACPI: Preparing to enter system sleep state S3
[20689.314869] PM: Saving platform NVS memory
[20689.322916] Disabling non-boot CPUs ...
[20689.425516] CPU 1 is now offline
[20689.529390] CPU 2 is now offline
[20689.633239] CPU 3 is now offline
[20689.633721] Extended CMOS year: 2000
[20689.633972] ACPI: Low-level resume complete
[20689.634014] PM: Restoring platform NVS memory
[20689.634776] Extended CMOS year: 2000
[20689.634814] Enabling non-boot CPUs ...
[20689.634938] Booting Node 0 Processor 1 APIC 0x2
[20689.634939] smpboot cpu 1: start_ip = 98000
[20689.645955] Calibrating delay loop (skipped) already calibrated this CPU
[20689.666263] NMI watchdog enabled, takes one hw-pmu counter.
[20689.666527] CPU1 is up
[20689.666635] Booting Node 0 Processor 2 APIC 0x1
[20689.666636] smpboot cpu 2: start_ip = 98000
[20689.677552] Calibrating delay loop (skipped) already calibrated this CPU
[20689.697923] NMI watchdog enabled, takes one hw-pmu counter.
[20689.698177] CPU2 is up
[20689.698295] Booting Node 0 Processor 3 APIC 0x3
[20689.698296] smpboot cpu 3: start_ip = 98000
[20689.709310] Calibrating delay loop (skipped) already calibrated this CPU
[20689.729767] NMI watchdog enabled, takes one hw-pmu counter.
[20689.730007] CPU3 is up
[20689.733993] ACPI: Waking up from system sleep state S3
[20689.755990] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI
[20689.759014] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI
[20689.759618] pcieport 0000:00:1c.4: wake-up capability disabled by ACPI
[20689.759672] PM: early resume of devices complete after 6.711 msecs
[20689.759746] i915 0000:00:02.0: setting latency timer to 64
[20689.759770] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[20689.759774] snd_hda_intel 0000:00:1b.0: setting latency timer to 64
[20689.759831] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[20689.759833] pciehp 0000:00:1c.7:pcie04: pciehp_resume ENTRY
[20689.759870] [drm] nouveau 0000:01:00.0: We're back, enabling device...
[20689.759883] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[20689.760847] xhci_hcd 0000:0b:00.0: setting latency timer to 64
[20689.760865] usb usb2: root hub lost power or was reset
[20689.760867] usb usb3: root hub lost power or was reset
[20689.761259] xhci_hcd 0000:0b:00.0: irq 46 for MSI/MSI-X
[20689.761264] xhci_hcd 0000:0b:00.0: irq 47 for MSI/MSI-X
[20689.761268] xhci_hcd 0000:0b:00.0: irq 48 for MSI/MSI-X
[20689.761273] xhci_hcd 0000:0b:00.0: irq 49 for MSI/MSI-X
[20689.761278] xhci_hcd 0000:0b:00.0: irq 50 for MSI/MSI-X
[20689.761409] ahci 0000:00:1f.2: setting latency timer to 64
[20689.761422] snd_hda_intel 0000:01:00.1: setting latency timer to 64
[20689.761445] r8169 0000:05:00.0: wake-up capability disabled by ACPI
[20689.761751] nouveau 0000:01:00.0: power state changed by ACPI to D0
[20689.761756] nouveau 0000:01:00.0: power state changed by ACPI to D0
[20689.761762] nouveau 0000:01:00.0: power state changed by ACPI to D0
[20689.761766] nouveau 0000:01:00.0: power state changed by ACPI to D0
[20689.761774] nouveau 0000:01:00.0: setting latency timer to 64
[20689.761779] [drm] nouveau 0000:01:00.0: POSTing device...
[20689.761782] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD5E7
[20689.774182] sd 0:0:0:0: [sda] Starting disk
[20689.784035] [drm] nouveau 0000:01:00.0: 0xD591: i2c wr fail: -6
[20689.800203] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[20689.824021] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xDC43
[20689.850844] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xEE49
[20689.850849] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEE4D
[20689.850901] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEF35
[20689.850902] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEF9A
[20689.870726] [drm] nouveau 0000:01:00.0: Restoring GPU objects...
[20689.893735] [drm] nouveau 0000:01:00.0: Reinitialising engines...
[20689.894216] [drm] nouveau 0000:01:00.0: Restoring mode...
[20690.093725] ata6: SATA link down (SStatus 0 SControl 300)
[20690.109722] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[20690.121944] ata5.00: configured for UDMA/100
[20690.197774] usb 4-1.2: reset low-speed USB device number 7 using ehci_hcd
[20690.549310] usb 1-1.4: reset full-speed USB device number 3 using ehci_hcd
[20690.644061] btusb 1-1.4:1.0: no reset_resume for driver btusb?
[20690.644070] btusb 1-1.4:1.1: no reset_resume for driver btusb?
[20690.713076] usb 1-1.5: reset high-speed USB device number 4 using ehci_hcd
[20692.674383] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[20692.675910] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[20692.677792] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[20692.678095] ata1.00: configured for UDMA/133
[20692.745040] PM: resume of devices complete after 2989.197 msecs
[20692.745315] PM: Finishing wakeup.
[20692.745316] Restarting tasks ... done.
[20692.751105] video LNXVIDEO:00: Restoring backlight state
[20692.751636] video LNXVIDEO:01: Restoring backlight state
[20692.818275] usb 4-1.6: new high-speed USB device number 8 using ehci_hcd
[20692.922948] usb 4-1.6: New USB device found, idVendor=0bda, idProduct=0138
[20692.922952] usb 4-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[20692.922954] usb 4-1.6: Product: USB2.0-CRW
[20692.922956] usb 4-1.6: Manufacturer: Generic
[20692.922958] usb 4-1.6: SerialNumber: 20090516388200000
[20692.954814] scsi8 : usb-storage 4-1.6:1.0
[20693.087102] usb 4-1.6: USB disconnect, device number 8
[20693.480310] r8169 0000:05:00.0: eth0: link down
[20693.481192] ADDRCONF(NETDEV_UP): eth0: link is not ready
[20693.484207] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[20693.490804] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[20693.607035] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[20693.607042] device wlan0 entered promiscuous mode
[20694.224663] atkbd serio0: Unknown key pressed (translated set 2, code 0x8d on isa0060/serio0).
[20694.224666] atkbd serio0: Use 'setkeycodes e00d <keycode>' to make it known.
[20694.521700] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[20694.523644] wlan0: authenticated
[20694.523864] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[20694.527461] wlan0: RX AssocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=4)
[20694.527470] wlan0: associated
[20694.531703] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[20704.938465] wlan0: no IPv6 routers present
[20722.946202] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 0
[20739.539139] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[20739.561826] cfg80211: Calling CRDA to update world regulatory domain
[20739.568766] cfg80211: World regulatory domain updated:
[20739.568780] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[20739.568783] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[20739.568786] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[20739.568788] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[20739.568790] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[20739.568792] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[20739.568795] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[20739.568797] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[20739.568800] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[20742.807574] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[20742.810529] wlan0: authenticated
[20742.811170] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[20742.814530] wlan0: RX ReassocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=4)
[20742.814543] wlan0: associated
[20752.900405] wlan0: no IPv6 routers present
[20771.103511] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 0
[21152.229851] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = c0:ac:54:f7:23:85 tid = 6
[21206.211459] usb 4-1.2: USB disconnect, device number 7
[21227.861823] usb 2-2: new low-speed USB device number 3 using xhci_hcd
[21227.906834] usb 2-2: New USB device found, idVendor=15d9, idProduct=0a4d
[21227.906844] usb 2-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[21227.906850] usb 2-2: Product:  USB OPTICAL MOUSE
[21227.907165] usb 2-2: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[21227.924211] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:1c.4/0000:0b:00.0/usb2/2-2/2-2:1.0/input/input23
[21227.924581] generic-usb 0003:15D9:0A4D.0005: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:0b:00.0-2/input0
[21904.681263] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[21904.690297] cfg80211: Calling CRDA to update world regulatory domain
[21904.707415] device wlan0 left promiscuous mode
[21904.711039] cfg80211: World regulatory domain updated:
[21904.711042] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[21904.711045] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[21904.711046] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[21904.711048] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[21904.711050] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[21904.711051] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[21904.711053] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[21904.711054] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[21904.711056] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[21907.006154] iwlwifi 0000:09:00.0: L1 Disabled; Enabling L0S
[21907.012796] iwlwifi 0000:09:00.0: Radio type=0x2-0x2-0x1
[21907.125353] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[21907.125361] device wlan0 entered promiscuous mode
[21908.222882] wlan0: authenticate with c0:ac:54:f7:23:85 (try 1)
[21908.225815] wlan0: authenticated
[21908.226327] wlan0: associate with c0:ac:54:f7:23:85 (try 1)
[21908.229522] wlan0: RX AssocResp from c0:ac:54:f7:23:85 (capab=0x411 status=0 aid=4)
[21908.229530] wlan0: associated
[21908.233401] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[21918.679745] wlan0: no IPv6 routers present
[21919.712023] wlan0: deauthenticating from c0:ac:54:f7:23:85 by local choice (reason=3)
[21919.718649] cfg80211: Calling CRDA to update world regulatory domain
[21919.725089] cfg80211: World regulatory domain updated:
[21919.725093] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[21919.725096] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[21919.725098] cfg80211:     (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[21919.725100] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[21919.725103] cfg80211:     (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[21919.725105] cfg80211:     (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[21919.725108] cfg80211:     (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[21919.725110] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[21919.725112] cfg80211:     (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[21920.409914] wlan0: authenticate with 02:1a:11:f5:c0:a2 (try 1)
[21920.413118] wlan0: authenticated
[21920.413611] wlan0: associate with 02:1a:11:f5:c0:a2 (try 1)
[21920.417155] wlan0: RX AssocResp from 02:1a:11:f5:c0:a2 (capab=0x411 status=0 aid=1)
[21920.417166] wlan0: associated
[21920.421554] cfg80211: Calling CRDA for country: BO
[21920.429550] cfg80211: Regulatory domain changed to country: BO
[21920.429553] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[21920.429556] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[21920.429558] cfg80211:     (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm)
[21924.380115] iwlwifi 0000:09:00.0: Tx aggregation enabled on ra = 02:1a:11:f5:c0:a2 tid = 0
[21931.191525] wlan0: no IPv6 routers present
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 11/12/2014 - 09:18
נושא ההודעה:

תיקון טעות קורה הרבה שכן מתחבר אבל לא גולש לאתרים

תודה לעוזרים
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 18/12/2014 - 22:58
נושא ההודעה:

חבר'ה אני ממש זקוק לעזרה אני לא מצליח לפתור אותה
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 19/12/2014 - 00:45
3 נושא ההודעה:

אם הבעיה אצלך נמצאת בקופסא של הוט, אז אף אחד פה לא יוכל לעזור.
אתה צריך לברר איתם. (הציוד שלהם לא אי אי אי ...)
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 19/12/2014 - 09:45
נושא ההודעה:

Anonymous :
תיקון טעות קורה הרבה שכן מתחבר אבל לא גולש לאתרים

תודה לעוזרים

פתח כמה טרמינלים -
1) תן פינג רציף לראוטר
2) תן פינג רציף ל 8.8.8.8
לא מכיר את hotbox אבל בטח יש שם חלון דיאגנוסטיקה שבו כתוב הuptime של הסשן (כמה זמן אתה מחובר) או אפילו אולי ישנה אפשרות לתת פינג מהראוטר עצמו החוצה.

המטרה בבדיקות לאבחן ולמקד את הבעיה (ניתוקים) -
בין המחשב לראוטר, או מהראוטר החוצה או אולי בכלל בעיית ריזולבינג. (ולכן פינג ל8.8.8.Cool
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אורח · ·
 

הודעה פורסם: 19/12/2014 - 10:11
נושא ההודעה:

די בטוח שהבעיה היא אצלי

מפני שכל המחשבים האחרים מתחברים כמו שצריך לראוטר וגם אני אחרי שאני מפעיל את המחשב בפעם הראשונה

אבל שאני נכנס לvm (יש לי 'windows xp בתור Guest) מתחיל לי כל הבעיות (רק לא מזמן שמתי לב לזה )

הנה הping לראוטר

קוד:
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_req=1 ttl=64 time=157 ms
64 bytes from 192.168.1.1: icmp_req=2 ttl=64 time=78.6 ms
64 bytes from 192.168.1.1: icmp_req=3 ttl=64 time=100 ms
64 bytes from 192.168.1.1: icmp_req=4 ttl=64 time=21.4 ms
64 bytes from 192.168.1.1: icmp_req=5 ttl=64 time=43.8 ms
64 bytes from 192.168.1.1: icmp_req=6 ttl=64 time=66.8 ms
64 bytes from 192.168.1.1: icmp_req=7 ttl=64 time=88.8 ms
64 bytes from 192.168.1.1: icmp_req=8 ttl=64 time=112 ms
64 bytes from 192.168.1.1: icmp_req=9 ttl=64 time=32.8 ms
64 bytes from 192.168.1.1: icmp_req=10 ttl=64 time=55.5 ms
^Z


הping ל8.8.8.8
קוד:

PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_req=1 ttl=51 time=146 ms
64 bytes from 8.8.8.8: icmp_req=2 ttl=51 time=169 ms
64 bytes from 8.8.8.8: icmp_req=3 ttl=51 time=90.7 ms
64 bytes from 8.8.8.8: icmp_req=4 ttl=51 time=112 ms
64 bytes from 8.8.8.8: icmp_req=5 ttl=51 time=170 ms
64 bytes from 8.8.8.8: icmp_req=6 ttl=51 time=159 ms
64 bytes from 8.8.8.8: icmp_req=7 ttl=51 time=159 ms
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
אלכס___אורח · ·
 

הודעה פורסם: 19/12/2014 - 17:35
נושא ההודעה:

עכשיו אני חושב שהבנתי את הבעיה שלך.
הבעיה היא לא בלינוקס אלה עם המכונה הווירטואליט של XP כשאת מחובר רק דרך הWIFI.

הסיבה לכך היא פשוטה.
כול פעם שחיבור הWIFI נופל בלינוקס יש סיכוי גבוה שכתובת הIP הפנימית תתחלף לכתובת שונה ממה שהמכונה של XP חושבת שהיא נמצאת בה ולכן אין לך רשת יצבה במכונה של XP.

יש לך כמה פתרונות לבעיה כמו:
להגדיר בנתב שלך הקצאת כתובות IP לפי כתובות ה MAC של כרטיסי הרשת שלך.
קוד:

שאלה הבאה אמורה לעזור לך להכווין את התמיכה הטכית של הוט.
Hot To Assigning a fixed local IP address to a particular MAC address in hotbox OR fiberbox

או לבצעה רסולבינג במכונה של XP כל פעם שמתחלפת כתובת IP:
קוד:

http://windows.microsoft.com/en-US/windows-xp/help/networking/repair-network-connection
http://forums.cnet.com/7723-6142_102-587346/how-do-i-repair-network-connections/#message5430855


בהצלחה
 
   
תגובה  עם ציטוט חזרה למעלה
חזרה לתוכן הדיון
הצגת הודעות מלפני:     
מעבר אל:  
כל הזמנים הם GMT + 2 שעות
תגובה לנושא
צפיה בנושא הבא Printable version התחבר כדי לבדוק הודעות פרטיות צפיה בנושא הקודם
PNphpBB2 © 2003-2004 

תוכן הדיון

  1. אורח
  2. אורח
  3. אורח [אלכס___]
  4. אורח
  5. אורח
  6. אורח
  7. אורח [אורח II]
  8. אורח
  9. אורח
  10. אורח [צפריר]
  11. אורח
  12. אורח
  13. אורח [אלכס___]
  14. אורח
  15. אורח [אלכס___]
  16. אורח
  17. אורח
  18. אורח
  19. אורח
  20. אורח
  21. אורח
  22. אורח
  23. אורח [אלכס___]