פורסם: 28/09/2012 - 08:36
נושא ההודעה: הפעלת רכיב COM בלוח אם
|
אז ככה:
מישהו מצא בעבודה מחשב-מסך מגע מהראשונים (אלה שהותקנו בקופות בסופרים).
המגע לא עובד...
מה עשינו?
מצאנו את הPDF של המסך מגע וגילינו שהרכיב טאץ' מחובר לכניסת COM ייעודית על הלוח.
הרצנו lshw ובדו"ח HTMLי קיבלתי ש: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor בצבע אדום (למיטב הבנתי זה אומר אחד משני דברים- או שאין דרייבר או שהרכיב לא פעיל...)
הרצנו lspci ולא נתן לנו הרבה אינפורמציה...
מה עכשיו?
עשיתי ls ל /dev ואין שם איזשהו COM (האם אמור להיות?)
אני יודע שנראה כאילו אני יודע להתמצא, אבל אני לא מגדיר עצמי בתור יותר מסתם NUB.
מערכת: xubuntu 12.04 - ממשק X לא מסיבה מיוחדת, רק לחסוך במשאבים...
כל עזרה תתקבל בברכה,
תודה.
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 11:09
נושא ההודעה:
|
קוד: | /dev/ttyS0 /dev/ttyS1 |
יש להם שמות שונים בלינוקס, זה לא נקרא com
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 11:22
נושא ההודעה: OK...
|
אז להצעתו של חבר עשיתי:
cat לרכיב, בזמן שאני נוגע במסך.
מצאתי:
ttyS0
ttyS1
ttyS10
.
.
.
ttyS19
קיבלתי:
0 כלום
1 כלום
10-19 Input Output error
רעיונות נוספים?
מישהו?
תודה.
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 11:26
נושא ההודעה:
|
זה אומר שרק com1, com2 פעילים בלוח שלך (ttyS0, ttyS1).
להבא תנסה:
קוד: |
dd if=/dev/ttyS0 | hexdump -C
|
עכשיו תשובה קונקרטית: אם אתה לא מקבל משהו מ־COM1, COM2... זה אומר שהרכיב לא מחובר לשם... נכון? אני חושב שאתה עדיין בשלב של בעיות חומרה.
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 11:33
נושא ההודעה:
|
הרצת lspci ככה: lspci -vvv ?
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 12:07
נושא ההודעה: אז שוב... תודה רבה על העזרה...
|
א. elcuco, צדקת... פתאום גיליתי שיש לי גם ttyS2-9 מתוכם (כצפוי, כי יש על המכונה הזו גם פיכסדוס): ttyS2-5 לא מחזירים שגיאת IO. עם זאת dd לא נותן לי כלום, הוא טוען ש- 0 בתים הועתקו. מה זה אומר לדעתך? הרכיב TOUCH מחובר ל-COM5 (את זה אני יודע מהאינטרנט), האם זה אומר ttyS4? אני מניח שכן. האם זה עוזר לי?
ב. אורח, תודה על ההצעה. להלן הOUTPUT אני לא מוצא את זה עוזר יותר מה-LSHW:
קוד: |
00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
Subsystem: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at <unassigned> (32-bit, prefetchable)
Capabilities: [40] Vendor Specific Information: Len=05 <?>
Kernel driver in use: agpgart-intel
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
Subsystem: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
Subsystem: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation 82852/855GM Integrated Graphics Device
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e8180000 (32-bit, non-prefetchable) [size=512K]
Region 2: I/O ports at e300 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: i915
Kernel modules: intelfb, i915
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
Subsystem: Intel Corporation 82852/855GM Integrated Graphics Device
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e8100000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: i915
00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Latitude X300
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Latitude X300
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at e100 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Latitude X300
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e200 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at e8200000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: e8000000-e80fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Kernel modules: iTCO_wdt, intel-rng
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation Device 24c2
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f000 [size=16]
Region 5: Memory at 3e000000 (32-bit, non-prefetchable) [size=1K]
Kernel driver in use: ata_piix
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02)
Subsystem: Intel Corporation Device 24c2
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 5
Region 4: I/O ports at 0500 [size=32]
Kernel modules: i2c-i801
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02)
Subsystem: Device 414c:4740
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at e500 [size=256]
Region 1: I/O ports at e600 [size=64]
Region 2: Memory at e8201000 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at e8202000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_intel8x0
Kernel modules: snd-intel8x0
01:02.0 Ethernet controller: Atheros Communications Inc. AR5212/AR5213 Wireless Network Adapter (rev 01)
Subsystem: Wistron NeWeb Corp. CM9 Wireless a/b/g MiniPCI Adapter
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e8000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: ath5k
Kernel modules: ath5k
01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at e8010000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
|
[/code]
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 12:14
נושא ההודעה:
|
רגע... com5? זה אומר שהוא מחובר ב־usb למארח...?
מה אתה רואה ב־lsusb ?
האם אתה רואה /dev/ttyUSB0 במערכת שלך?
מה אתה רואה ב־dmesg?
(להציג את lspci היה מיותר... הבקר com שלך לא מחובר דרך אפיק ה־pci שלך ... נכון?)
|
|
חזרה לתוכן הדיון |
פורסם: 28/09/2012 - 12:46
נושא ההודעה:
|
|
|
חזרה לתוכן הדיון |
פורסם: 01/10/2012 - 01:14
נושא ההודעה:
|
|
|
חזרה לתוכן הדיון |
פורסם: 01/10/2012 - 04:11
נושא ההודעה:
|
וכמובן:
ls -l /dev/serial/by-id
|
|
חזרה לתוכן הדיון |
פורסם: 03/10/2012 - 10:36
נושא ההודעה:
|
תודה על כל הנסיונות...
SO FAR לא ממש הולך לנו...
אין לי serial בתוך dev.
וכנראה רכיב הTOUCH הוא של TOUCHIT (אל תשאלו אותי...)
אני הולך לנסות עם פיכסדוס 7 סטארטר...
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 10:18
נושא ההודעה: צעד קדימה, שניים אחורה...
|
טוב.
אז הדרייבר של POSTouch אצלי (הצלחתי בעזרת היצרן).
ועכשיו UBUNTU הצליחו לעצבן אותי בפעם השלישית בחודשיים האחרונים באותו נושא:
xorg.conf
אני לא מצליח (ולפני כמה שבועות ניסיתי וגם לא הצלחתי)
ליצור את xorg.conf!!
אני משתגע מזה!
מישהו הצליח ב 12.04 ליצור את הקובץ?
אולי להסביר לי איך לכתוב אותו מ-0.
בדקתי בכשלוש מאות טוטריאלים באינטרנט ואפ'חד לא עזר לי...
מה שקורה זה שבמסגרת הפעלת הדרייבר עלי להוסיף SECTION לקובץ, אבל היות והקובץ לא קיים ב 12.04 ואני לא מצליח ליצור אותו... You do the math...
אניוואן?
בבקשה...
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 10:23
נושא ההודעה:
|
xorg.conf כבר מזמן בוטל וזה ממש לא קשור לאובונטו. אני מציע לך להסתכל ב:
קוד: |
ls -l /usr/share/X11/xorg.conf.d/
|
ואולי לעשות חיפוש באינטרנט במקום להפריח האשמות שמבוססות (בלי להעליב) על דעות קדומות ובורות.
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 10:29
נושא ההודעה:
|
ניסית ללא הקובץ?
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 12:05
נושא ההודעה:
|
Anonymous : | xorg.conf כבר מזמן בוטל וזה ממש לא קשור לאובונטו. אני מציע לך להסתכל ב:
קוד: |
ls -l /usr/share/X11/xorg.conf.d/
|
ואולי לעשות חיפוש באינטרנט במקום להפריח האשמות שמבוססות (בלי להעליב) על דעות קדומות ובורות. |
א. אני מהתחלה טענתי שאני בור (NUB)
ב. אני התבססתי על מה שמצאתי באינטרנט (החל מאובונטו 9.10 בערך ביטלו את הקובץ או משהו כזה), יותר מהשמועות האלה אני לא מכיר. מתנצל מעומקי ליבי, ודאי שלא התכוונתי לפגוע ברגשות של איש...
ג.
קוד: |
-rw-r--r-- 1 root root 1099 Aug 4 04:53 10-evdev.conf
-rw-r--r-- 1 root root 590 Jun 14 01:45 11-evdev-quirks.conf
-rw-r--r-- 1 root root 364 Jun 14 01:45 11-evdev-trackpoint.conf
-rw-r--r-- 1 root root 956 Jul 3 07:05 50-synaptics.conf
-rw-r--r-- 1 root root 115 Jun 14 09:13 50-vmmouse.conf
-rw-r--r-- 1 root root 842 Mar 30 2012 50-wacom.conf
-rw-r--r-- 1 root root 590 Jul 3 07:04 51-synaptics-quirks.conf
|
ד. WobnI - work,
מה זה אומר ללא הקובץ?
אלה הוראות היצרן:
http://www.axoncomputer.it/download/Common/POS_Touch/Linux/POSTouch_install_RS232.htm
אני הלכתי לפיהן...
תודה, ושוב סליחה.
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 12:21
נושא ההודעה: ורק לפרוטוקול
|
גם אם אובונוטו עיצבן אותי אני עדיין מאוד אוהב את המ"ה הזו.
הכעס נובע מאכזבה, על כך שהמוצא האחרון שלי עלול (רחמנא) להיות פיכסדוס...
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 12:22
נושא ההודעה:
|
הכוונה היא לעלות ללא xorg.conf
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 12:37
נושא ההודעה:
|
WobnI - work : | הכוונה היא לעלות ללא xorg.conf |
לעלות?
אני מצטער... לא הבנתי.
דבר אלי כמו אל החמור שאני:
"תלחץ על הכפתור עם הציור של העיגול והצ'ופצ'יק הקטן למעלה.
חכה קצת.
.
.
.
ברכותי עלית ללא xorg.conf! "
משהו דומה...
תודה.
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 12:40
נושא ההודעה:
|
|
|
חזרה לתוכן הדיון |
פורסם: 04/10/2012 - 15:36
נושא ההודעה:
|
אלון : | אני לא מצליח (ולפני כמה שבועות ניסיתי וגם לא הצלחתי)
ליצור את xorg.conf!!
אני משתגע מזה!
מישהו הצליח ב 12.04 ליצור את הקובץ?
אולי להסביר לי איך לכתוב אותו מ-0.
בדקתי בכשלוש מאות טוטריאלים באינטרנט ואפ'חד לא עזר לי...
מה שקורה זה שבמסגרת הפעלת הדרייבר עלי להוסיף SECTION לקובץ, אבל היות והקובץ לא קיים ב 12.04 ואני לא מצליח ליצור אותו... You do the math...
אניוואן?
בבקשה... |
לפני שבוע התקנתי לניסיון את Vectorlinux. לאחר שעברתי בשלום את תעתועי ההתקנה הטקסטוריאלית שלה , הסתבר לי שמעמדו של הקובץ (xorg.conf) התדרדר כל כך שאפילו מערכת ההפעלה עצמה מתעלמת מקיומו.
כן כן, תוכנה שמתעלמת מקיומו של קובץ הקונפיגורציה שלה. לא להאמין. פעם ראשונה שאני נתקל בדבר כזה. ולמה אני מספר לך את זה? כדי שלא תתלה יותר מידי תקוות באיקס אורג נקודה קוף.
ולמה "קוף"?
כי לפעמים נדמה לי שמנהלי כמה מין ההפצות זוללים יותר מידי בננות מקולקלות...
|
|
חזרה לתוכן הדיון |
פורסם: 05/10/2012 - 08:10
נושא ההודעה:
|
תודה על האזהרה.
בינתיים יש התקדמות בתמיכה של היצרן גם עם הפיכסדוס (שגם שם לא עבד המגע...)
אנחנו (זה אני, אנוכי, עצמי וכל החברה שאיתי...) נעדכן בהמשך. יכול להיות שגם ככה הדרייבר לא נכון...
|
|
חזרה לתוכן הדיון |
פורסם: 05/10/2012 - 09:13
נושא ההודעה:
|
באיזה שלב יצירת הקובץ נכשלה?
שים לב, שאולי היית צריך לעצור את מנהל החלונות של xfce - מנהל החלונות שלו זה Xfwm4
|
|
חזרה לתוכן הדיון |
פורסם: 05/10/2012 - 17:04
נושא ההודעה:
|
איקס אורג נקודה קוף : | באיזה שלב יצירת הקובץ נכשלה?
שים לב, שאולי היית צריך לעצור את מנהל החלונות של xfce - מנהל החלונות שלו זה Xfwm4 |
בוצע,
הצלחתי ליצור xorg.conf והוא שם עלי כ-ז-ה פס.
אני משוכנע שמה שחסר לי זה ליצור קובץ conf ייעודי לinput ולכתוב בו את מה שנדרש לפי ההוראות המקוריות, אבל...
רעיונות?
|
|
חזרה לתוכן הדיון |
פורסם: 05/10/2012 - 18:07
נושא ההודעה:
|
מה מראה הפלט? קוד: | grep "Monitor" -A7 /etc/X11/xorg.conf
|
|
|
חזרה לתוכן הדיון |
פורסם: 05/10/2012 - 20:42
נושא ההודעה:
|
קוד: |
touch@touch-screen:~$ grep "Monitor" -A7 /etc/X11/xorg.conf
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor1"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor2"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Monitor"
Identifier "Monitor3"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
### <percent>: "<f>%"
--
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
--
Monitor "Monitor1"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
--
Monitor "Monitor2"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
--
Monitor "Monitor3"
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
touch@touch-screen:~$
|
|
|
חזרה לתוכן הדיון |
|